Rocktron MIDI Xchange Manual do Utilizador

to midi inback panel ofprocessorConnection using a Rocktron HEX pedal and a non-Rocktroneffects processor

Functions and Control Layout

Functions and Control Layout continued...

Display - This three segment display will show you the presetyou are on or which MIDI Channel is currently assigned (seeSetting MIDI Channel section f

567MIDI OUT Jack - This Jack is used to connect to various MIDIdevices. Using a standard 5-Pin MIDI Cable or the RocktronRMM900 7-Pin MIDI Cable conn

UP Switch - This switch will allow you to scroll up to the desiredpreset. You may scroll up in two ways:1) By depressing the switch and releasing it

MIDI Xchange Operation - Power SourcesThe MIDI XChange is unique in respect that you may use mostany type of power.9-VOLT BATTERYThe MIDI XChange is s

POWER ON SEQUENCESELECTING AND RECALLING PRESETSWhen power is applied using the Power switch (see point 2), theMIDI XChange’s display a blue LED will

UP, DOWN and RECALL SwitchesThese switches will allow you to change presets or MIDI channels.The range is 1-128 for the presets and 1-16 for the MIDI

Now preset number 1 is still selected. To select preset 35 depressand release the RECALL switch. The display will now show thenumber 35:At this poin

Copyright © 2003 GHS CorporationAll Rights Reserved.Your MIDI XChange™ pedal has been tested and complies with the followingStandards and Directives a

SMART CONTROLLER PORTSWhat are “SMART CONTROLLERS”Typically with most MIDI footcontrollers, when using continuouscontroller pedal(s) the “status” of t

HOW TO USE THE CC17 and CC7 PORTS:Connections - when using the Rocktron HEX Volume/Expressionpedal use a stereo to stereo 1/4 jack cable (not include

CC17 Port - This controller port is the default volume controllerfor all Rocktron products. Thus, all you need to do to control thevolume of each pre

2) Press and hold the DOWN switch3) While holding down the DOWN switch press the UP Switchand release both.The display of the MIDI XChange should be

To select the MIDI Channel depress and release the RECALLswitch once. The display will immediately go back to the selectingand recalling preset mode

MIDI MESSAGEMIDI CHANNEL = 1- 16 [0H-FH]PROGRAM CHANGE MESSAGE:[PC COMMAND || MIDI CHANNEL] = 0C0H[VALUE] = 1-128 [000H-07FH]COMPLETE MESSAGE = 0C0 07

Rack Gear:Gainiac (preamp w/12ax7 tube)Chameleon 2000 (preamp w/multi-effects)RepliTone MP(modelling preamp w/multi-effects)Xpression (multi-effects

Electric Guitar - Acoustic Guitar and Bass Amplifiers:Vendetta Head(100 W Head 4-Channels All Tube - MIDI Switchable)Vendetta Combo (100W 2x12 Combo C

Rocktron - A Division of GHS Corporation2813 Wilber AveBattle Creek MI 49015USARocktron Phone: 1-(269)-968-3351Email: [email protected]

Do not block any ventilation openings (if applicable). Install in accordance with themanufacturer’s instructions.Do not install near any heat sources

IntroductionCongratulations on your purchase of the Rocktron MIDIXChange. The MIDI XChange is a simple to use, yetmultifunctional MIDI switcher that

Basic Connection with an effect processor

Connection using a Rocktron Xpression and Phantom Power

Connection when using a rack system from midi outto midi infrom midi out/thruto midi in of second effects proc

Connection using a Rocktron Xpression with a Bass amplifier

Connection using a Rocktron HEX Pedal and Xpression Processor